How the effective use of hardware tools
Posted on: August 18, 2011
Use pliers is right-handed operation. The jaw toward the inside, easy to control the clamp cuts and, with little finger extended in the middle of the two clamp handle to resist clamp handle, open clamp head, so that separate clamp handle flexible.
Plier has 150,175,200 common electrical and 250mm and other specifications. Inside or outside according to type of work need to buy. Pliers Sabertooth also be used to fasten or loosen the nut.
Pliers to cut wire used to split the soft rubber or plastic insulation.
The blade can also be used pliers to cut wire cutting, wire. No. 8 galvanized iron wire cutting, the application of cutting edge around the back and forth several times, and then just gently pull, or broken wire.
Voltage I also used to cut wire, steel wire metal wire so hard.
Pliers plastic pipe insulation voltage 500V or more, it can be charged with cutting wires. Avoid the use of throw, so as not to damage the insulation of plastic pipe.
Do not make the pliers as a hammer.
Can not live with the double-stranded wire cutting pliers, will short circuit.
Fixed with pliers pull winding hoop when I clipped the wire pliers teeth, clockwise spiral.
Revised nose pliers, commonly known as needle-nosed pliers, electrician in particular, is commonly used inside electrical tools. Mainly used to cut smaller diameter single-unit and multi-strand and single strand wire to bend lap joints, strip the plastic insulation and so on.
Wire connector with needle-nosed pliers bend the operation method is: first thread left off, and then close the right turn screw clockwise direction Serve.
Needle-nosed pliers a little restructuring, can be used for stripping needle-nosed pliers. Methods are: electric drill in nose pliers with cutting blades of the preceding line drill? 0.8,? 1.0mm 2 slot, and then respectively 1.2,1.4 mm drill bit slightly expanded look at Note: do not extend through the, so that the two a thin slot edge. Thus, one can cut line but also stripping the needle-nosed pliers to change it!
Stripping for the inside electrical, electrical repair, electrical instruments commonly used tools. It is suitable for plastic, rubber insulated wire, cable core wire stripping. Use are: stripping of the thread will be placed on the edge clamp head, the hand of the two clamp handle pinch, then a loose, insulating skin and core line will be torn off.
Use pliers
Fuer up to tell you the secret: Mo to handle when the clamp head clamp. Remember, remember.
Use pliers is right-handed operation. The jaw toward the inside, easy to control the clamp cuts and, with little finger extended in the middle of the two clamp handle to resist clamp handle, open clamp head, so that separate clamp handle flexible.
Plier has 150,175,200 common electrical and 250mm and other specifications. Inside or outside according to type of work need to buy. Pliers Sabertooth also be used to fasten or loosen the nut.
Pliers to cut wire can be used to split flexible rubber or plastic insulation.
The blade can also be used pliers to cut wire cutting, wire. No. 8 galvanized iron wire cutting, the application of cutting edge around the back and forth several times, and then just gently pull, or broken wire.
Voltage mouth can also be used to cut off wire, steel and other hard metal wire.
Pliers plastic pipe insulation voltage 500V or more, it can be charged with cutting wires. Avoid the use of throw, so as not to damage the insulation of plastic pipe.
Do not make the pliers as a hammer.
Can not live with pliers cut double strand wire will short circuit.
Fixed with pliers Pull clamp winding when the pliers mouth clamped tooth wire wound in a clockwise direction.
Revised nose pliers, commonly known as needle-nosed pliers, electrician in particular is one of the tools used inside electrical. Mainly used to cut smaller diameter single-unit and multi-ply yarn and a single strand of wire bent ring joints, strip the plastic insulation and so on.
Wire connector with needle-nosed pliers bend the operation method is: first thread left off, and then close the right turn screw clockwise direction Serve.
Little restructuring needle-nosed pliers, needle-nosed pliers can be used for stripping. Methods are: electric drill in the use of needle-nosed pliers wire cutting blade preceding drill? 0.8,? 1.0mm 2 slot, and then respectively 1.2,1.4 mm drill bit extended look NOTE: Do not wear the expansion, so that the two a thin slot edge. Thus, one can cut line can change the stripping of the needle-nosed pliers on it!
Stripping for the inside electrician, electrical repairs, electric instruments one of the tools used. It is suitable for plastic, rubber insulated wire, cable core wire stripping. Use is: The thread will be placed in stripping pliers head edge, the hand of the two clamp handle pinch, then a loose, insulating skin and core line will be torn off.
Pliers is a tool used for fastening, and some pliers also has a cut off function. Pliers (see Figure 5-19) of many types, but they have one for clamping part of the material, known as the "jaws." Jaw with the lever control, can produce large clamping force.
Pliers to use: In general, the limited strength of pliers, it is not enough for its operation of the power of the general hand-reach work. Especially the smaller models or ordinary needle-nosed pliers, bend strength with which the bar when the board may be damaged jaw. There are three general Cutting pliers edge, not only can be used to cut wire can be used to cut wire. clamp handle can only use hand, can not be augmented by other means (such as playing with a hammer, Taiwanese tiger clamp, etc.). Needle-nosed pliers to grip as shown in Figure 5-20.
Plier has 150,175,200 common electrical and 250mm and other specifications. Inside or outside according to type of work need to buy. Pliers Sabertooth also be used to fasten or loosen the nut.
Pliers to cut wire used to split the soft rubber or plastic insulation.
The blade can also be used pliers to cut wire cutting, wire. No. 8 galvanized iron wire cutting, the application of cutting edge around the back and forth several times, and then just gently pull, or broken wire.
Voltage I also used to cut wire, steel wire metal wire so hard.
Pliers plastic pipe insulation voltage 500V or more, it can be charged with cutting wires. Avoid the use of throw, so as not to damage the insulation of plastic pipe.
Do not make the pliers as a hammer.
Can not live with the double-stranded wire cutting pliers, will short circuit.
Fixed with pliers pull winding hoop when I clipped the wire pliers teeth, clockwise spiral.
Revised nose pliers, commonly known as needle-nosed pliers, electrician in particular, is commonly used inside electrical tools. Mainly used to cut smaller diameter single-unit and multi-strand and single strand wire to bend lap joints, strip the plastic insulation and so on.
Wire connector with needle-nosed pliers bend the operation method is: first thread left off, and then close the right turn screw clockwise direction Serve.
Needle-nosed pliers a little restructuring, can be used for stripping needle-nosed pliers. Methods are: electric drill in nose pliers with cutting blades of the preceding line drill? 0.8,? 1.0mm 2 slot, and then respectively 1.2,1.4 mm drill bit slightly expanded look at Note: do not extend through the, so that the two a thin slot edge. Thus, one can cut line but also stripping the needle-nosed pliers to change it!
Use pliers
Fuer up to tell you the secret: Mo to handle when the clamp head clamp. Remember, remember.
Use pliers is right-handed operation. The jaw toward the inside, easy to control the clamp cuts and, with little finger extended in the middle of the two clamp handle to resist clamp handle, open clamp head, so that separate clamp handle flexible.
Plier has 150,175,200 common electrical and 250mm and other specifications. Inside or outside according to type of work need to buy. Pliers Sabertooth also be used to fasten or loosen the nut.
Pliers to cut wire can be used to split flexible rubber or plastic insulation.
The blade can also be used pliers to cut wire cutting, wire. No. 8 galvanized iron wire cutting, the application of cutting edge around the back and forth several times, and then just gently pull, or broken wire.
Voltage mouth can also be used to cut off wire, steel and other hard metal wire.
Pliers plastic pipe insulation voltage 500V or more, it can be charged with cutting wires. Avoid the use of throw, so as not to damage the insulation of plastic pipe.
Do not make the pliers as a hammer.
Can not live with pliers cut double strand wire will short circuit.
Fixed with pliers Pull clamp winding when the pliers mouth clamped tooth wire wound in a clockwise direction.
Revised nose pliers, commonly known as needle-nosed pliers, electrician in particular is one of the tools used inside electrical. Mainly used to cut smaller diameter single-unit and multi-ply yarn and a single strand of wire bent ring joints, strip the plastic insulation and so on.
Wire connector with needle-nosed pliers bend the operation method is: first thread left off, and then close the right turn screw clockwise direction Serve.
Little restructuring needle-nosed pliers, needle-nosed pliers can be used for stripping. Methods are: electric drill in the use of needle-nosed pliers wire cutting blade preceding drill? 0.8,? 1.0mm 2 slot, and then respectively 1.2,1.4 mm drill bit extended look NOTE: Do not wear the expansion, so that the two a thin slot edge. Thus, one can cut line can change the stripping of the needle-nosed pliers on it!
Stripping for the inside electrician, electrical repairs, electric instruments one of the tools used. It is suitable for plastic, rubber insulated wire, cable core wire stripping. Use is: The thread will be placed in stripping pliers head edge, the hand of the two clamp handle pinch, then a loose, insulating skin and core line will be torn off.
Pliers is a tool used for fastening, and some pliers also has a cut off function. Pliers (see Figure 5-19) of many types, but they have one for clamping part of the material, known as the "jaws." Jaw with the lever control, can produce large clamping force.
Pliers to use: In general, the limited strength of pliers, it is not enough for its operation of the power of the general hand-reach work. Especially the smaller models or ordinary needle-nosed pliers, bend strength with which the bar when the board may be damaged jaw. There are three general Cutting pliers edge, not only can be used to cut wire can be used to cut wire. clamp handle can only use hand, can not be augmented by other means (such as playing with a hammer, Taiwanese tiger clamp, etc.). Needle-nosed pliers to grip as shown in Figure 5-20.